Planning solar, a battery or a charger
Read the rate before you buy, ask installers better questions, and know which federal credits have ended.
- Start with
- Your rate, your bills and what you might add
- Ask installers
- For estimates on your rate, not only yearly totals
- Federal credits
- 25D, 25C, 30D and 30C have ended
- Culni does not
- Sell or install hardware, or give tax advice

Most homeowners plan solar, a battery or a charger from the equipment side: how many panels fit on the roof, how big a battery, how many amps for the charger. The rate usually comes last, as a yearly savings figure at the bottom of a proposal. Culni works the other way round. The rate decides what each kWh is worth in each hour, and that decides which equipment earns its keep and how it should run.
Rate first
Before you talk to installers, find four things on your bill and your utility’s rate schedule:
- The rate you are on, and the ones you could choose. Many utilities offer a flat rate and one or more time-of-use rates, sometimes with limits. LG&E and KU’s RTOD-Energy, for example, needs an AMI meter and is capped at 500 customers.
- The peak windows and how they change by season. A summer afternoon peak overlaps with solar production. A winter morning peak does not.
- The export credit. What your utility credits for a kWh sent to the grid decides how much solar is worth when nobody is home to use it. For LG&E systems under NMS-2 it is $0.07089 per kWh, against an energy charge of $0.11499 on Rate RS (effective September 1, 2026, before riders and taxes).
- How your use falls across the day. If your utility lets you download hourly usage from a smart meter, do it. Monthly totals cannot show how much of your use lands in the peak.
The utility bill checklist shows where to find each item, and the rate plan comparison calculator shows how the share of use in peak hours decides which rate is cheaper.
Example (fictional). Here is the example home on one clear April weekday, built up in stages. Each row shows the net cost for the day on the example time-of-use rate (8 cents off-peak, 14 cents in the day, 31 cents from 4 to 9 p.m.) and on the 13 cent flat comparison rate, both with a 7 cent export credit.
| What the house has | Example time-of-use rate | Flat comparison rate |
|---|---|---|
| No equipment, 29.0 kWh of household use | $5.17 | $3.77 |
| Plus 7.6 kW of solar | $1.35 | $0.52 |
| Plus a 13.5 kWh battery and one EV (11.1 kWh a day), default settings | $2.52 | $1.49 |
| The same, with a Culni schedule | $0.60 | $1.49 |
The cheaper rate flips in the last row. In the first three rows the flat rate costs less on this day. With the battery and the car scheduled, the time-of-use rate costs $0.89 less. On the flat rate the hour of use does not change the price, so the battery’s self-use mode is already the right setting and the figure stays at $1.49. Fixed charges are left out, and one clear spring weekday is not a year: a real plan compares every day type against your own bills.
Questions to ask installers
- Can you show the production estimate by month, and by hour if possible, rather than only a yearly total?
- What will my bill look like on my current rate, and on each rate I could switch to? Which export credit did you assume, and is it the one that applies to a new system?
- For a battery: what are the usable capacity and the power rating, which circuits will it back up, and does my interconnection agreement allow charging from the grid?
- After commissioning, how can the inverter, battery and charger receive instructions: a manufacturer app, a local network interface, an open protocol? Can a third party schedule them with my permission?
- For a charger: what amperage does my panel allow, and can the charger or the car schedule charging by time?
- Which tax credits or incentives did you assume, and are they still available on the date the system will be placed in service?
The home battery checklist and the EV charger installation checklist go further, and the battery sizing worksheet turns a list of critical loads into a daily kWh figure.
Federal tax credits: what ended and when
Checked November 22, 2026, against the IRS pages linked below. Some installer pages and older articles still quote these credits as available.
| Credit | What it covered | When it ended |
|---|---|---|
| Residential Clean Energy Credit (25D) | 30% of qualified costs for solar, battery storage of at least 3 kWh and other property | Not allowed for expenditures made after December 31, 2025. An expenditure counts as made when installation is complete, so paying in 2025 for a system installed later does not qualify. |
| Energy Efficient Home Improvement Credit (25C) | Up to $2,000 a year for qualified heat pumps and heat pump water heaters | Not allowed for property placed in service after December 31, 2025 |
| New Clean Vehicle Credit (30D) | New electric vehicles | Not available for vehicles acquired after September 30, 2025 |
| Alternative Fuel Vehicle Refueling Property Credit (30C) | For a main home, 30% of the cost of charging equipment, up to $1,000 per item, in eligible census tracts | Not allowed for property placed in service after June 30, 2026 |
The changes come from Public Law 119-21 of July 4, 2025, and the IRS explains them in its FAQs on the modified credits. This is general information, not tax advice. Ask a tax professional about your own situation.
With the credits gone, equipment carries its full cost, so sizing it against your actual rate matters more.
What Culni does and does not do
Culni does not sell or install hardware, and it gives no tax or legal advice. Before you buy, it can read your rate and your bills and show in writing how the equipment you are considering would run on your rate, with every assumption listed, so you can compare that with an installer’s proposal. After installation, it writes and runs the schedule. Wiring, protection settings and interconnection stay with your installer and your utility, as the installers page explains, and device connection is confirmed home by home.
What you send and what you get
Send your utility and rate plan, up to twelve months of bills (one is enough to start), the equipment you are considering with any installer proposals, and your goals: lower bills, backup, or both. You get your rate decoded, a rate comparison for each option, an hour-by-hour schedule for each day type showing how the equipment would run, and the estimated value with every input shown. Fill in the home energy inventory worksheet first, then send it through Check my home.
TodayYour turn
Send your rate and your devices
Your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan: your rate decoded, which devices can connect, the daily schedule and its estimated value with every assumption shown.
Remote. No site visit needed.