Devices and connections
Which kinds of devices a schedule can use, and how each connection is confirmed in your home first.
- You send
- Make and model of each device and a screenshot of its app
- Culni checks
- The control path for each device in your home
- You get
- A connection table: connected, read-only or manual
- Never touched
- Wiring, protection settings and export limits

Many homes with solar, a battery and an EV have equipment from several makers, each with its own app and its own idea of your rate. Culni writes one schedule across them. Whether a particular device can follow that schedule depends on the device, its software and your home, so device connection is confirmed home by home. This page explains which kinds of devices a schedule can use, the ways devices accept instructions, and how a connection is checked before anything is promised.
Device categories
| Category | What the schedule uses it for | What Culni reads | What it may instruct, with your permission |
|---|---|---|---|
| Solar inverters | Knowing how much solar is coming and where it goes | Production, export, status | Usually nothing; export settings stay as installed |
| Home batteries | Storing energy for the expensive hours | State of charge, mode, power | Charge, hold and discharge timing, above your reserve |
| EV chargers and vehicles | Charging in the cheapest window, ready by departure | Plug-in status, charge level, power | Start and stop times, charging power |
| Smart thermostats | Pre-heating and pre-cooling before a peak | Temperature, setpoints, mode | Setpoint shifts within the comfort limits you set |
| Heat pump water heaters | Heating water when energy is cheap | Tank temperature, mode | Heating times and setpoints within your limits |
| Smart panels | Seeing use by circuit, and switching flexible circuits | Power by circuit | Switching circuits you approve, such as a pool pump |
Solar inverters
The inverter is the schedule’s best source on solar production and export. Culni usually only reads it. Inverter protection settings, grid-support settings and export limits were set by your installer for your interconnection agreement, and they stay that way. How exported solar is credited is on solar export.
Home batteries
The battery is where most of the daily value sits. The schedule decides when it charges, holds and discharges, never below the reserve you choose, and only charges it from the grid where the battery and your interconnection agreement allow it. See battery scheduling and backup reserve.
EV chargers and vehicles
Charging can often be controlled through the charger, through the vehicle, or both. Which one works best depends on what each exposes in your home. The goal is the same either way: charge in the cheapest window that still has the car ready when you leave. See EV charging.
Smart thermostats, water heaters and other flexible loads
A heat pump can warm or cool the house ahead of a peak, and a heat pump water heater can heat its tank when energy is cheaper. You set the comfort limits; the schedule works inside them. Pool pumps and dryers can move too. See flexible loads.
Smart panels
A panel that measures each circuit shows where the energy goes, which improves the estimate. Some can also switch individual circuits. Culni only uses circuits you approve for switching, and never changes how the panel is wired.
How devices accept instructions
These are the usual control paths. None of them is assumed to work in your home until it has been checked.
- Manufacturer cloud interfaces. Many devices report to the maker’s online service and take instructions from it. Access is granted through a permission on your account with that maker. What a third party may read or change is the maker’s decision, and it can change.
- Local network interfaces. Some devices accept instructions over your home network. Whether that route is available, and safe to use, depends on the device and on your network.
- Open protocols (industry context). Parts of the industry use published standards to connect devices. IEEE 2030.5 defines how a utility can communicate with home energy equipment, including time of day pricing and EVs. OCPP is an open protocol between charging stations and the systems that manage them; version 2.0.1 was approved as IEC 63584 in 2024. OpenADR is a standard for demand response signals. They are described here as context. Culni does not claim support for or certification under any of them.
- Settings you enter yourself. Many devices have a built-in schedule or a time-based mode. When no other path works, this is the manual route.
How a connection is checked for your home
- You list the device. Make, model and, if you can, a screenshot of the app’s settings or information screen. The home energy inventory worksheet has a row for each.
- Culni identifies the possible paths for that model and notes them in the home energy plan as “to confirm”.
- You give permission for each device you want connected, in the way that path requires.
- Culni reads first. If the device reports its state reliably, read access is confirmed.
- Culni confirms an instruction arrives, using a harmless change at a time you agree, such as moving a charging start time and moving it back.
- The result goes in the connection table: connected, read-only or manual, with a note on what happens if the path stops working.
Paths can change after a firmware update, a new app version or a change in the maker’s policy. If a path stops working, the device keeps running on its own settings, the schedule for it pauses, and you are told what changed and what to do.
What “manual” means
A device is manual when Culni cannot send it instructions in your home: there is no path, the maker does not allow it, or you prefer not to grant control. A manual device stays in the plan. Culni gives you the settings to enter by hand, such as a 1 a.m. charging start in the car’s app or a heating schedule for the water heater, and the estimate counts them. What manual settings cannot do is change day by day for weather, departures or storm watches, and the estimate says so.
Example (fictional). In one home the battery and the EV charger connect, the solar inverter is read-only, and the water heater has no usable path. The plan lists the water heater as manual with a schedule to set on its control panel: heat from 1 to 5 a.m. on weekdays. Everything else follows the daily schedule.
What Culni does not touch
- Wiring, breakers, panels and transfer equipment.
- Inverter protection and grid-support settings, and export limits set for your interconnection agreement.
- Device firmware and manufacturer safety limits.
- The battery below your reserve.
- Devices you have not listed and approved, or any device after you withdraw permission.
What Culni reads and how permissions work are on security and data.
If you are choosing equipment
Ask the seller what the device lets other software read and control, and whether that depends on an account, a subscription or a local connection. The home battery checklist and the EV charger installation checklist list the questions. You can also send the models you are considering; the plan will say what is known about their control paths, marked unconfirmed until the device is installed in your home.
TodayYour turn
Send your rate and your devices
Your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan: your rate decoded, which devices can connect, the daily schedule and its estimated value with every assumption shown.
Remote. No site visit needed.