For installers and electricians
Where Culni picks up after commissioning, and what stays with the installer.
- You send
- The commissioning summary, with the homeowner's permission
- The homeowner gets
- A written schedule and a monthly bill check
- You get back
- Flags on any setting that is yours to change
- Stays with you
- Wiring, protection, export limits and warranty work

Commissioning ends with a system that works. Then the homeowner lives with it on their electricity rate, and the questions start: why the battery is empty at 7 p.m., why the bill went up after the car arrived, why the app shows more solar than the bill credits. Culni picks up at that point. It writes the homeowner’s daily schedule from their rate, explains it in writing and checks it against every bill. Everything you are responsible for stays with you.
Culni is a new company. There are no partnerships, referral fees or installer programs to join. If that ever changes, this page will say so.
Where Culni fits
| Stage | Who |
|---|---|
| Design, permits, installation, interconnection, commissioning | You |
| Wiring, protection settings, export limits, backup circuits | You, under the utility’s requirements |
| Decoding the homeowner’s rate | Culni |
| Daily timing of the battery, EV charging and flexible loads | Culni, through control paths confirmed for that home |
| Monthly comparison of the estimate with the bill | Culni |
| Hardware faults, warranty claims and manufacturer support | You and the manufacturer |
Culni does not sell or install hardware, so it is not competing for your next job. It does not change wiring, protection settings or interconnection settings, and it does not replace you or the manufacturer’s support.
What helps Culni start well
With the homeowner’s permission, the commissioning summary answers most of what the schedule needs to know:
- Inverter and battery makes, models and firmware versions.
- The export limit and any other settings required by the interconnection agreement.
- Whether the battery may charge from the grid under that agreement.
- The backup configuration: whole-home or partial, which circuits are backed up, and the transfer equipment.
- Where the metering points sit, so production and use are read correctly.
- For EV chargers: the circuit size and the current the charger is set to draw.
- The net metering tariff the system is on (at LG&E and KU, NMS-1 or NMS-2).
Culni treats all of these as fixed. The schedule works inside them.
What you get back
A written plan the homeowner understands. The home energy plan explains, hour by hour, what the battery and the car charger will do and why. With the homeowner’s permission, you can have a copy.
Flags, not changes. If a setting that belongs to you looks wrong for the homeowner’s rate (a backup circuit list that leaves out the refrigerator, a grid-charging permission that was never set, an export limit lower than the paperwork), Culni flags it to the homeowner and, with their permission, to you. Culni does not change it.
Fewer “why is my bill high” calls. Every month the bill check compares the estimate with the actual bill and explains each difference: weather, use, a rate change, a program event or a device that did not follow the schedule. The most common confusion is solar. LG&E and KU put it plainly on their own net metering page: “Generation does not equal credit.” The net meter records only the energy that flows onto the grid, and the credit covers energy charges, not the basic service charge. A written explanation of that, each month, is a call you do not have to take.
Why the schedule matters after commissioning in Kentucky
At LG&E and KU, solar systems first in service on or after September 24, 2021 are on net metering service NMS-2. LG&E credits each exported kWh at $0.07089 and KU at $0.07534, while LG&E’s residential energy charge is $0.11499 per kWh (base charges effective September 1, 2026, before riders and taxes). For an LG&E customer, a kWh used at home is worth about 4.4 cents more than the same kWh exported. That gap is what a battery schedule and a car-charging window earn from, and it is set by the tariff, not by the hardware. More on solar export.
Kentucky law also requires customer generating systems and interconnection equipment to meet NEC, IEEE and testing-laboratory safety and power quality standards. That work is yours, and Culni stays out of it.
What Culni will not do
- Change wiring, breakers, protection or grid-support settings, export limits or backup circuits.
- Install firmware, or change anything covered by the interconnection agreement.
- Take a referral fee or offer one.
- Handle warranty claims or hardware faults.
- Promise the homeowner a connection it has not confirmed. Device connection is confirmed home by home; see devices.
Starting a conversation
Write to hello@culni.com, or use the contact page. Say which systems you commission (solar, batteries, EV chargers or panel work), in which utility areas, and the questions your customers ask most after the install. A homeowner who wants a plan can send their own details through the same page; the how it works page shows what happens next.
TodayYour turn
Send your rate and your devices
Your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan: your rate decoded, which devices can connect, the daily schedule and its estimated value with every assumption shown.
Remote. No site visit needed.