11 a.m. to 4 p.m.
4 to 9 p.m.
in the example home
Flexible loads
Water heating, pre-cooling, pool pumping and laundry moved to better hours, within your comfort limits.
- 11 a.m. to 4 p.m. heat water, run the pool pump
- 4 p.m. to 9 p.m. flexible loads wait
- You send
- Device list with models, thermostat, comfort limits
- You get
- A window for each load and day type, and settings to enter
- Stays with you
- Comfort limits and any manual change you make
- Limits
- Automatic control only where a path is confirmed

Some loads care about a result, not an hour. You want hot water in the morning, a comfortable house at 6 p.m., a clean pool and dry laundry. When the heating, cooling, pumping or drying happens can move, within limits. Those are flexible loads. On a time-of-use rate, or with solar surplus that only earns an export credit, moving them is often the cheapest change a home can make. It matters beyond one house, too: Lawrence Berkeley National Laboratory notes that buildings account for three-fourths of US electricity use, and a national goal aims to triple the energy efficiency and demand flexibility of buildings by 2030, relative to 2020.
Heat pump water heaters
A water heater tank is a store of heat. A heat pump water heater can heat the tank in hours of cheap energy or surplus solar and coast through the peak. The schedule:
- heats in solar surplus hours or off-peak, whichever your rate makes cheaper;
- keeps the minimum tank temperature you set, and has the tank reheated by the time you need hot water;
- avoids the resistance elements where it can. Many heat pump water heaters also have electric resistance elements that use far more power than the heat pump, and a high-demand mode or a heavy draw can switch them on. The plan recommends the mode that keeps them off during the peak, where the heater’s controls allow it.
Heating and cooling: pre-heat and pre-cool
The house itself stores heat. Cooling a degree or two below your usual setting before a summer peak, then letting the temperature drift up through it, moves cooling energy into cheaper hours. In winter, rates with a morning peak make pre-heating before dawn useful. LG&E and KU’s RTOD-Energy rate, for example, has a weekday peak from 6 to 10 a.m. (Eastern Standard Time) from November to March, as well as an evening one.
Heat pumps need care. A deep setback followed by a fast recovery can bring on auxiliary electric heat, which uses far more power than the heat pump itself. The schedule moves the setpoint in small steps and stays inside the band you set, so a pre-heat does not cost more than it saves. How long a house can coast depends on its insulation and air sealing; the first monthly bill check shows how yours behaves, and the schedule is adjusted from there.
Pool pumps
A pool pump needs a number of hours of filtration a day, set by you or your pool service. Those hours can sit in solar surplus or off-peak hours, and a variable-speed pump can run longer at a lower speed. The schedule never cuts the daily run time below what you set.
Dryers, dishwashers and the loads you start
Most appliances you start by hand have no control path at all, and that is fine. The plan lists the best hours for each day type, and a delay-start button on the appliance does the rest.
Example (fictional). On the example rate, energy costs 31 cents per kWh from 4 to 9 p.m. on weekdays, 14 cents in day hours and 8 cents off-peak, and surplus solar that would be exported earns 7 cents. A 5,000 W electric dryer run for an hour 12 times a month uses 60 kWh: $18.60 a month at the peak, $8.40 in day hours and $4.80 off-peak, as the appliance energy cost calculator shows. Run in hours of solar surplus, each kWh costs only the 7 cent credit it would have earned. Most of the value is in leaving the peak. Once a load is out of it, the choice between off-peak and surplus hours is worth about a cent per kWh, and convenience can decide.
Comfort limits come first
| Load | What moves | The limit you set | Usual window on the example rate |
|---|---|---|---|
| Heat pump water heater | When the tank reheats | Minimum tank temperature; hot water by a set time | Solar surplus around midday, or off-peak |
| Heating and cooling | Pre-heat or pre-cool, then coast | A temperature band for each part of the day | Before the 4 p.m. peak |
| Pool pump | Run hours | Minimum hours per day | Solar surplus hours |
| Dryer, dishwasher | Start time | Done by a time you choose | Off-peak or solar surplus hours |
If you change the thermostat yourself, your change wins. The schedule picks up again at its next block, and if you override the same block often, the plan asks whether the limit should change.
Utility programs and overrides
Utilities often target these loads with thermostat and water heater programs and with rebates for using less during peak events. LG&E and KU’s Peak Time Rebates, for example, offer “$1 per kWh saved”. Culni is not affiliated with LG&E, KU or any utility program, and it does not enroll you. If you join a program, its event control or event hours take priority on event days. Your plan says what Culni does then, for example whether to pre-cool before an event starts, where the program’s rules and your comfort band allow it.
What Culni will not do
- It will not take a room, the tank or the pool outside the limits you set.
- It will not install controllers, change wiring or alter a water heater’s safety settings.
- It will not promise a control path it has not confirmed. Device connection is confirmed home by home through the connection check, and anything that cannot connect gets a written setting instead.
What you send and what you get
Send a list of your flexible loads with makes and models: the water heater, the thermostat and the heating and cooling system, the pool pump, the dryer. Add your comfort limits and the times you need hot water. The home energy inventory worksheet has columns for all of it. You get a window for each load and day type, automatic control only where a confirmed path exists, and the settings to enter by hand where it does not. For a quick look at what moving use out of the peak is worth, try the time-of-use savings calculator.
TodayYour turn
Send your rate and your devices
Your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan: your rate decoded, which devices can connect, the daily schedule and its estimated value with every assumption shown.
Remote. No site visit needed.