Culni homeCheck my home
Menu

Smart thermostat demand response and peak time rebates: are they worth it?

How smart thermostat demand response programs, peak time rebates and critical peak pricing pay, what pilots found, and when an event costs you money.

Reader question
Should I enroll my smart thermostat in my utility's demand response or peak time rebate program, and how do these programs pay?
A V of geese flies low over a frosted field at dusk, the lead bird dropping back as another moves up to take the point.

For most homes with central air conditioning or a heat pump, enrolling a smart thermostat in a utility program is worth trying, as long as you read the terms first: the payments are modest, you can override any event, and the real costs show up on time-of-use rates and on cold winter mornings. Device programs pay you for enrolling and for each event or season; peak time rebates pay per kWh you use below an estimated baseline, with no penalty if you use more; critical peak pricing raises your price sharply during declared events. In published pilots, critical peak pricing produced the largest cuts in peak use and peak time rebates smaller ones, and both did better when a thermostat or switch did the work automatically.

This article separates those designs, reads real terms from Portland General Electric and from LG&E and KU in Kentucky, summarizes what the pilots measured, and works through two fictional event days to show where the money goes. It ends with a checklist you can hold any program against. Program details below were read in November 2026 and change often, so check your own utility’s current terms.

The three program designs you are likely to be offered

A smart thermostat demand response program is any arrangement in which your utility, or a company working for it, asks your heating and cooling to use less power during a few high-demand hours and pays you for it. The payment can come from the program, from a rebate per kWh, or from avoiding a high event price.

Design How you are paid What you risk Who controls the thermostat
Bring-your-own-thermostat (device program) A fixed amount to enroll, then per event or per season Comfort for a few hours; some programs require you to stay in for a share of event hours The program adjusts the setpoint; you can override
Peak time rebate A rebate per kWh below your estimated baseline during events Nothing on the bill if you use more; a low rebate if your baseline is low You do, by hand or with your own automation
Critical peak pricing A lower price most hours, a much higher price during declared events A higher bill if you use power during events You do
Direct load control (older switch programs) A credit per event or per month Comfort; the compressor is cycled off A switch on the outdoor unit

The first three are the designs this article focuses on. Switch programs still exist, but LG&E and KU, for example, stopped installing new switches on January 14, 2023, according to their Kentucky tariff, and existing switches stay in the program until they fail.

Device programs

In a device program, you enroll the thermostat, often through the thermostat maker’s app, and the program sends event signals to it. LG&E and KU’s Bring Your Own Thermostat program describes the deal plainly: “Get paid to let us adjust the temperature on your Wi-Fi connected thermostat by a few degrees during times of high-energy demand,” with signups through the thermostat maker’s web or app platform. Portland General Electric’s Smart Thermostat program works the same way and pays by season rather than by event.

Peak time rebates

A peak time rebate (PTR) leaves your normal rate alone. On event days, the utility compares your metered use during the event with an estimate of what you would have used, called the baseline, and pays for the difference. The Green Mountain Power study defined it simply: “During peak hours customers earn rebates by reducing their electricity usage below a baseline level.” You lose nothing if you ignore an event. That makes PTR the lowest-risk design, and also the one where your payment depends most on how the baseline is built.

Critical peak pricing

Critical peak pricing (CPP) is a rate, not a rebate. You pay a somewhat lower price most of the time and a much higher price during a limited number of declared events. It pays best for households that can reliably cut use during events and costs most for those that cannot. When the Connecticut evaluation described below was published in 2014, its authors noted that only one percent of US households were on any form of dynamic pricing. The pilot evidence on critical peak pricing is still the clearest yardstick for the other two designs.

What happens during a thermostat event, hour by hour

A typical event has four stages: notice, preconditioning, the event itself and recovery. The details differ by program and thermostat maker, so these are the terms to look for.

Stages of a summer thermostat event laid over a fictional time-of-use dayThe top band shows the example rate: day price until 4 p.m., peak from 4 to 9 p.m., off-peak after 9 p.m. Below it, the program pre-cools from 4 to 5 p.m., holds the setpoint 3 degrees warmer during the event from 5 to 8 p.m., and the air conditioner recovers from 8 to 9 p.m. Both the pre-cooling hour and the recovery hour fall inside the time-of-use peak.Example rateDay, 14 centsPeak, 31 cents8 centsProgram eventEvent, 3 degrees warmerPre-coolRecoveryAir conditionerkWh per hour1 p.m.4 p.m.8 p.m.11 p.m.
Example (fictional) data using the site's example rate (day 14 cents, peak 4 to 9 p.m. at 31 cents, off-peak 8 cents per kWh). Bar heights: 2.0 kWh per hour on a normal afternoon, 2.8 kWh while pre-cooling, 1.0 kWh during the event, 3.0 kWh during recovery, then 1.5 and 1.0 kWh as the evening cools. Event stages follow the program terms described in the text.
  1. Notice. Google’s Nest help page on Rush Hour Rewards says customers get a message the night before a morning event and at least an hour before an afternoon event. Portland General Electric says its peak time rebate customers receive day-ahead and day-of notices, according to the utility’s presentation on a DOE Better Buildings call in April 2024.
  2. Preconditioning. Many programs pre-cool or pre-heat the house before the event so it has room to drift. Portland General Electric’s terms say: “An hour before a Peak Time Event, your thermostat pre-heats or pre-cools your home.” Nest describes the same step and labels it on the thermostat display.
  3. The event. The program moves your setpoint a few degrees. Portland General Electric changes it by 1 to 3 degrees for events lasting 1 to 4 hours. In NREL’s field tests of cold-climate heat pumps, presented on the same DOE call, each site had a maximum indoor temperature offset, with a default of 4°F.
  4. Recovery. When the event ends, the thermostat returns to your schedule. The heating or cooling then runs hard to recover the lost degrees, and that recovery is where much of the hidden cost sits.

You can step in at any stage on a certified thermostat. ENERGY STAR’s key product criteria for certified smart thermostats require the ability to work with utility programs while preserving “consumers’ ability to override those grid requests.” What overriding costs you is set by each program’s terms, covered below.

What the pilots found about peak time rebates and critical peak pricing

Controlled pilots consistently found that households cut peak use when events are called, that critical peak pricing produced larger cuts than rebates, and that automatic control of air conditioning raised the response under both designs. They also found that savings per event are small in dollars and vary a lot from one event to the next.

Connecticut: price designs compared side by side

The Connecticut Light & Power Plan-It Wise Energy Pilot ran from June to September 2009 with about 2,200 customers, and Ahmad Faruqui, Sanem Sergici and Lamine Akaba published the evaluation in The Energy Journal in 2014. The utility called ten critical peak days, from 2 to 6 p.m., on a day-ahead basis. Critical peak customers paid $0.86 to $1.82 per kWh during those hours on an all-in basis; peak time rebate customers kept the standard rate (about $0.201 per kWh all-in) and could earn rebates of $0.78 to $1.74 per kWh. Some customers in each group also had a thermostat the utility could adjust or a switch on the air conditioner compressor.

Residential design (Connecticut, 2009) Peak reduction on event days, price only With thermostat or compressor switch
Critical peak pricing, high and low price variants 16.1% and 10.2% 23.3% and 15.1%
Peak time rebate, high and low rebate variants 10.9% and 7.0% 17.8% and 11.8%
Time-of-use rate with a noon to 8 p.m. peak 3.1% and 1.6% No added effect reported

The authors concluded that “equivalently designed PTR and CPP rates do not have equivalent impacts on peak demand,” and that the color-changing Energy Orb display had no measurable effect. The paper’s tables also show off-peak use on event days rising by 2.0 to 4.3 percent in the groups with automatic control, more than in the price-only groups, which fits the preconditioning and recovery effect described above.

Vermont: small savings per event, large variation

Green Mountain Power’s consumer behavior study, part of a DOE-funded smart grid project and evaluated by Seth Blumsack and Paul Hines in 2015, called fourteen critical peak events in 2012 and 2013, each from 1 to 6 p.m., with notice the evening before. The critical peak price and the rebate were both $0.60 per kWh. Customers on the rebate cut average hourly load during events by 0.038 to 0.081 kW (5 to 8 percent); customers on critical peak pricing by 0.045 to 0.142 kW (5 to 15 percent).

Three findings matter for a homeowner deciding today:

  • The money per event was small. Savings averaged $0.18 to $0.42 per customer per event, or $2.52 to $5.88 over all fourteen events.
  • Response varied from event to event. The authors observed “very little persistence among any treatment group on an event-to-event basis,” and no group responded consistently across the fourteen events.
  • Some savings moved rather than disappeared. “In some cases the savings from reduced consumption during the critical peak event are offset by increased consumption during the periods before and after the event.”

Customers on critical peak pricing were also nearly twice as likely to leave their assigned rate as rebate customers, which the authors read as dissatisfaction with the price risk.

What the pilots do and do not tell you

These pilots tested rate designs on whole-house use, mostly without the automatic thermostat control that device programs rely on. Their lesson for a thermostat owner is about direction, not size: automatic control raised the response in Connecticut, rebates produced less than equivalent prices, and the cash per event was modest. Your own result depends on your house, your equipment, your climate and the program’s terms.

How much the programs actually pay

In the programs read for this article, payments run from tens of dollars a year up to a tariff maximum of a few hundred, and the tariff maximum is not always what a program pays today. Read both the program page and, where it exists, the tariff sheet.

Program (terms read November 2026) Enrollment Ongoing payment Event limits
Portland General Electric, Smart Thermostat $25 $25 per summer and per winter season in which you take part in at least half of the event hours Summer: 8 to 9 events, typically 3 to 8 p.m. Winter: 3 to 4 events in one place on the page, 5 to 6 in its FAQ, typically 6 to 10 a.m. or 3 to 8 p.m. Events last 1 to 4 hours; none on holidays
LG&E and KU, Bring Your Own Device (tariff terms) Up to $50 per thermostat Up to $10 per event the device takes part in Up to 25 events a year; at most $300 per device in the first year and $250 a year after
LG&E and KU, Peak Time Rebates (web page) None stated “$1 per kWh saved” Not stated on the page
LG&E and KU, Peak Time Rebates (tariff terms) None Up to $2 per kWh below baseline, plus up to a $15 annual participation bonus Up to 25 events a year; requires an AMI meter

Sources: Portland General Electric program page; LG&E tariff P.S.C. Electric No. 14, Sheets No. 86.7 and 86.8, effective February 16, 2026 (KU’s tariff carries the same terms); LG&E and KU Peak Time Rebates page.

Two rules in those terms matter as much as the amounts. Portland General Electric says that because both of its programs reward shifting at the same peak times, “you can only be enrolled in one program at a time.” LG&E’s tariff reserves the right “to limit participation in multiple programs to prevent compensating a customer more than once for the same demand reduction.” Expect to choose one program per device.

Example (fictional). Suppose a household enrolls one thermostat and takes part fully in every event offered. In Portland General Electric’s program, the first year pays $25 to enroll plus $25 for summer and $25 for winter, $75 in all, and $50 a year after. Under LG&E and KU’s tariff maximums, 15 events at the full $10 would pay $50 + (15 x $10) = $200 in the first year. On LG&E and KU’s peak time rebate at the posted $1 per kWh, a home that beats its baseline by 2.5 kWh in each of 15 events would earn 15 x 2.5 x $1 = $37.50. These are hypothetical event counts and kWh, not program results; the actual numbers depend on how many events are called and on your baseline.

For scale, the site’s time-of-use savings calculator shows what moving everyday use out of a peak window is worth. Its default example, with the site’s fictional example rate (peak 31 cents, off-peak 8 cents), moves 90 kWh a month out of the peak and lowers the bill by $20.70 a month. Event programs pay for a few hours on a few days; a rate that rewards shifting every weekday can be worth more, if your household can shift.

Who tends to come out ahead

Whether a program is worth it depends less on the payment than on how your house and household respond to a few degrees of drift. These are rules of thumb drawn from the program terms and pilot results above, not predictions for any one home:

Your situation Likely fit Why
Central AC or heat pump, house holds temperature well, often away on weekday afternoons Good fit for a device program Events pass with little discomfort and few overrides
Home all day, sensitive to heat or cold Peak time rebate, or skip No penalty for using more; you choose event by event
Already on a time-of-use rate and shifting daily Device program only if event hours sit inside your peak Otherwise preconditioning and recovery can land in your expensive hours
Heat pump with large backup strips in a cold climate Summer events yes; winter events with care Recovery after a cold morning event can bring on resistance heat
Can cut use reliably on short notice, comfortable with bill risk Critical peak pricing, where offered Largest response in pilots, and the largest downside if you cannot follow through

Kentucky homes on LG&E and KU

For LG&E and KU customers, the current menu as of November 2026 is the Bring Your Own Thermostat program (enrollment through the thermostat maker’s app), Peak Time Rebates at the posted $1 per kWh, and the Online Marketplace, where the tariff allows discounts of up to $75 on smart thermostats. The switch-based Demand Conservation program is not accepting new enrollments. Each program needs its own sign-up, and the tariff’s double-payment rule means one device is usually enrolled in one program. Peak Time Rebates requires an AMI meter; check your bill or your account before enrolling.

Peak time rebates: the baseline decides the payment

On a peak time rebate, your payment is the gap between your baseline and your metered use during the event, so the way the baseline is built matters more than the rebate rate. LG&E’s tariff describes the method in general terms: savings are calculated “by comparing their metered consumption with an estimate of their baseline consumption during events,” and the program FAQ lists “How is my baseline calculated?” as a question to read before you enroll.

A baseline is an estimate, and every estimate has failure modes:

  • Habitual savers earn less. If you already keep the house warm in summer afternoons or are usually out, your baseline is low and there is little left to cut.
  • Unusual days distort it. A week of guests, a vacation or a heat wave before an event can push the baseline up or down.
  • Pre-cooling counts if it falls inside the event window. Use before the event starts does not reduce your rebate, but if your own schedule pre-cools during event hours, that use counts against you.
  • Weather may or may not be accounted for. Ask whether the baseline is adjusted for the event day’s temperature. Green Mountain Power’s pilot, for example, calculated reductions with the PJM Customer Baseline methodology, a published method from the regional grid operator.

The upside is that nothing extra is charged if you use more than the baseline. In the Connecticut pilot, rebate customers “were still subject to the standard CL&P rates,” and LG&E’s tariff describes a program that pays customers to reduce use. A peak time rebate is a free option. If an event lands on a day when you need the air conditioning, you simply earn nothing.

Pairing a rebate with automation

A rebate pays you for what you do; it does not adjust the thermostat for you. In the Connecticut pilot, rebate customers with an adjustable thermostat or compressor switch cut peak use by 11.8 to 17.8 percent, against 7.0 to 10.9 percent with the price signal alone. If your thermostat lets you schedule a warmer setpoint for event hours, or your utility’s notice can trigger an automation, you get the device-program behavior with the rebate’s lack of penalty. Check the program terms first: because of the double-payment rules above, you usually cannot also enroll the same thermostat in a device program.

Events on a time-of-use rate: when the program’s timing costs you

On a time-of-use rate, a thermostat event can save less than it appears, or cost money, because the program’s preconditioning and recovery hours may fall inside your own rate’s peak. Event windows and rate windows are set separately, and they do not always line up.

Portland General Electric’s summer events typically run between 3 and 8 p.m., while the utility’s own Time of Day rate prices weekdays from 5 to 9 p.m. higher, according to its presentation on the DOE call. In Kentucky, LG&E’s RTOD-Energy rate puts the weekday summer on-peak at 1 to 5 p.m. Eastern Standard Time, which is 2 to 6 p.m. on a daylight-time clock. A program event that starts late in that window and runs past it, or a pre-cooling hour that starts in it, shifts air conditioning use between on-peak and off-peak hours in ways the program does not track.

Example (fictional). A house on the site’s example rate (day 14 cents until 4 p.m., peak 4 to 9 p.m. at 31 cents, off-peak 8 cents after 9 p.m.) gets a summer event from 5 to 8 p.m. On a normal afternoon its air conditioner uses 2.0 kWh an hour from 4 to 9 p.m.: 10.0 kWh x $0.31 = $3.10.

On the event day, the program pre-cools from 4 to 5 p.m. (2.8 kWh), raises the setpoint 3 degrees from 5 to 8 p.m. (1.0 kWh an hour, 3.0 kWh) and recovers from 8 to 9 p.m. (3.0 kWh). Total from 4 to 9 p.m.: 2.8 + 3.0 + 3.0 = 8.8 kWh x $0.31 = $2.73. The bill saving on the rate is $3.10 - $2.73 = $0.37.

If this were a peak time rebate event and the baseline matched the normal afternoon, the reduction during event hours would be 6.0 - 3.0 = 3.0 kWh, worth $3.00 at $1 per kWh. Most of the day’s value comes from the event payment, not the rate.

Now suppose the household’s own schedule pre-cools from 2 to 4 p.m. instead, while the day price applies, adding 1.0 kWh at 14 cents ($0.14), so the program’s pre-cooling hour is not needed: 4 to 5 p.m. stays at 2.0 kWh. The peak total becomes 2.0 + 3.0 + 3.0 = 8.0 kWh x $0.31 = $2.48, plus $0.14 earlier: $2.62, a rate saving of $0.48 instead of $0.37. The difference is small on one day; it matters across a season of events and every non-event weekday.

Two practical rules follow:

  1. Pre-cool or pre-heat in your cheaper hours, not in the program’s hour. Our guide to pre-cooling and pre-heating covers how far ahead and by how many degrees, and when it stops paying.
  2. Watch where recovery lands. If the event ends before your rate’s peak ends, the catch-up runs at the peak price. A slower return to your normal setpoint keeps the recovery smaller.

Winter events, heat pumps and auxiliary heat

Winter events deserve more caution than summer ones in a heat pump home, because recovery after a cold morning event can bring on electric resistance backup heat. Strips use more electricity than the heat pump would for the same warmth, and on a rate with a winter morning peak, such as LG&E’s, that recovery can land inside the peak.

Programs do call winter events. Portland General Electric’s winter season runs November 1 through February, with events typically from 6 to 10 a.m. or 3 to 8 p.m., and its program is open to homes with an electric forced-air furnace or a ducted heat pump as well as central air conditioning. LG&E and KU’s tariff describes its device program as managing “summer and winter loads.”

The field evidence shows what can go wrong. In NREL’s tests of cold-climate heat pumps, presented on the April 2024 DOE call, units cut power by about 30% in general curtailment events and 60% in critical ones, and indoor temperatures rarely drifted past the 4°F default limit, even on the coldest days. But at one site, at the end of a 5 to 8 a.m. event, the slides show a “big spike in aux. power to make up room temperature,” and the summary notes that “some units used the Aux electric resistance after the DR events to recover to initial setpoint temperature.” ENERGY STAR’s criteria for smart thermostats require service providers to report electric resistance heat use for heat pumps, a sign of how much attention the issue gets.

Example (fictional). A heat pump home on LG&E’s RTOD-Energy rate, where the winter weekday on-peak runs 6 to 10 a.m. Eastern Standard Time at $0.19307 per kWh (base energy charge before riders and taxes, effective September 1, 2026), has a winter event from 6 to 8 a.m. The house drifts 3 degrees. At 8 a.m., still inside the rate’s peak, the thermostat calls for the lost degrees and runs 10 kW of backup strips for 30 minutes: 10 x 0.5 = 5.0 kWh x $0.19307 = $0.97.

Suppose the heat pump alone could deliver the same heat at a coefficient of performance of 2.5 (a hypothetical figure for this weather). It would use 5.0 / 2.5 = 2.0 kWh, or $0.39, taking longer. The strips cost $0.58 more for one recovery. A peak time rebate measured only during the event hours would not see that cost; the bill would.

What you can do about it:

  • Check how your thermostat handles auxiliary heat after an event. Google’s Nest help page on Heat Pump Balance, for example, describes an auxiliary heat lockout temperature and notes that the default setting, Max Comfort, “generally gives you higher AUX lockout temperature,” so the strips turn on sooner and more often. Other thermostats have their own settings. Our article on heat pump auxiliary heat and winter bills explains how to read and change them.
  • Opt out of the coldest mornings. On a day when the heat pump is already at its limit, the event saves little and recovery is likely to need strips.
  • Prefer smaller offsets in winter. A smaller drift leaves less heat to make up, so the thermostat is less likely to call for strips at the end of the event.
  • Ask whether winter events are optional or whether you can enroll for summer only. If not, the override is your tool.

Comfort, overrides and who is at home

ENERGY STAR certified thermostats must let you override an event, but each program decides what an override costs you, and most of the comfort risk falls on the people at home in the afternoon or early morning.

Read the override rules closely:

  • Per-season thresholds. Portland General Electric pays its seasonal reward only if you “participate in at least half of the Peak Time Event hours each season,” and it notes that if your air conditioning is turned off, “we can’t automatically adjust your temperature during peak times.”
  • Per-event payments. LG&E and KU’s tariff pays per event in which the device participates, so ask whether an override forfeits that event’s payment and how partial participation is treated.
  • Rebates. On a peak time rebate, overriding simply lowers your reduction and your rebate.

People override sooner when the change is larger. NREL’s comfort research, presented on the same DOE call, found that “larger automated setpoint changes are overridden faster.” That is useful for choosing a program and for setting your own limits: a program that moves the setpoint 1 to 3 degrees, like Portland General Electric’s, asks less of you than one that moves it 4.

Some households should think twice, or enroll with a plan to override freely: homes with infants, older adults or anyone whose health depends on a steady indoor temperature; homes with pets left alone in summer afternoons; and homes where someone sleeps during the day. Nothing in these programs is worth a risk to health. Portland General Electric’s terms let you change the setting at any time, and ENERGY STAR’s criteria require certified thermostats to preserve your ability to override.

Data sharing and control: what you hand over

Enrolling a thermostat gives a program the right to change your setpoint and may give it access to data about how your system runs. The terms that govern that access can sit in a separate document from the program page.

Look for who is involved. LG&E and KU route signups “through your smart thermostat manufacturer’s web or app-based platform.” Google’s Rush Hour Rewards overview says the program “is powered by Renew Home in partnership with Google Nest and your energy provider.” Portland General Electric’s page points to separate program terms and conditions on another website. A thermostat program can involve the utility, the thermostat maker and an outside program operator, each with its own privacy terms.

Questions to answer from the terms before you enroll:

  1. What data is collected? Setpoints, indoor temperature, run time, occupancy sensing and outdoor temperature are all possible.
  2. Who receives it, and for what? Event delivery, program evaluation and marketing are different uses.
  3. How long is it kept, and what happens when you leave?
  4. Can the program change settings beyond the event, such as schedules or equipment configuration?
  5. How do you unenroll? Portland General Electric, for example, lists an email address and phone number for leaving the program.

Our security and data page sets out what Culni reads and does not do with home energy data, which is a useful list of questions to ask any service that touches your thermostat.

How program events fit with a daily schedule

If you enroll, the utility’s event signal takes priority on event days, and everything else in the house should plan around it. Culni is software that reads a home’s electricity rate and runs one daily schedule across rooftop solar, a home battery, EV charging and flexible loads, including heating and cooling through the thermostat where its control path allows, and then checks the result against the bill each month.

Culni does not run demand response programs, is not affiliated with any utility program and does not enroll anyone. When a homeowner chooses to join a program, the home energy plan lists it with what Culni would and would not do on event days. On those days the program’s control wins, and the rest of the schedule is planned around it: pre-cooling can move into cheaper hours, and the water heater and EV charger can stay out of the event window. Where the program and the equipment allow, a gentler return to the normal setpoint keeps the recovery smaller. The flexible loads page describes how heating, cooling and water heating are scheduled against a rate, and the all-electric homes page shows how a heat pump fits into one plan.

A home battery or EV can also be enrolled in programs of its own, with different rules. Our article on virtual power plants covers battery programs and what they commit you to.

Checklist before you enroll a smart thermostat

Read the program page and the terms and conditions, then answer these questions. If a program will not answer one, treat that as part of the answer.

  1. Which design is it? Device program, peak time rebate or critical peak pricing. Only critical peak pricing charges a higher price for event hours.
  2. How many events a year, how long, at what hours, and in which seasons? Compare them with your rate’s peak windows.
  3. How far ahead are you notified?
  4. How much does the setpoint move, and does the program precondition the house first?
  5. What does an override cost? Per-event forfeit, a seasonal threshold or nothing.
  6. How is the baseline built, if it is a rebate? Which days, and is it adjusted for weather?
  7. What does it pay? Enrollment, per event, per season or per kWh, with any caps. Check the tariff sheet where there is one.
  8. Can you combine it with other programs? Usually not for the same device.
  9. Are winter events included, and can you join for summer only?
  10. How does your heat pump recover after a winter event? Check the auxiliary heat lockout and related settings before the first cold morning.
  11. What data is shared, with whom, and for how long?
  12. How do you leave, and do you keep what you earned?

What to do next

  1. Find your rate’s peak windows and write them next to the program’s typical event hours.
  2. Read the program terms in full, including the separate terms and conditions document.
  3. Set your thermostat’s limits first: the largest drift you will accept, the auxiliary heat lockout and a pre-cooling or pre-heating time in your cheaper hours.
  4. Enroll for one season and watch the bills. Compare event-day use with similar days, and note how often you overrode.
  5. Decide at the end of the season whether the payments justify the comfort and the recovery costs.

If you want those decisions made with your own rate, devices and bills, you can send your rate plan and device list and receive a written home energy plan that shows the schedule hour by hour, including how program events would be handled.

TodayYour turn

Want this worked out for your home?

Send your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan and every assumption behind it.

Remote. No site visit needed.