An LG&E or KU household saves on the optional RTOD-Energy rate only if less than about 22% of its electricity falls in weekday on-peak hours: 21.9% at LG&E and 22.1% at KU, using base energy charges effective September 1, 2026. Where your home lands depends on what it can move: an EV charged overnight, a battery or a timed heat pump and water heater pull the share down, while afternoon air conditioning and winter-morning heat push it up. RTOD-Demand pays only for homes with high monthly kWh and tightly controlled 15-minute peaks. Before switching, check your own on-peak share from your smart meter data, and note that each utility caps both time-of-day rates at 500 customers combined and makes you wait 12 months to return after leaving.
The rest of this guide sets the three residential rates side by side, explains when the on-peak hours fall on your clock, works out where each rate pays, and walks through three fictional households with current prices. All tariff values were checked on the Kentucky Public Service Commission’s copies of the LG&E and KU tariffs in November 2026. They are base charges before riders and taxes.
The three residential rates side by side
LG&E and KU each offer three rates to a single-family home: the standard Rate RS, with one price for every kWh, and two optional time-of-day rates. RTOD-Energy charges a lower price off-peak and a higher one on-peak. RTOD-Demand charges a low price per kWh plus two charges per kW of demand.
| Effective September 1, 2026 | LG&E | KU |
|---|---|---|
| Basic service charge, all three rates | $0.48 per day | $0.58 per day |
| Rate RS energy charge | $0.11499 per kWh | $0.11396 per kWh |
| RTOD-Energy off-peak | $0.09312 per kWh | $0.07811 per kWh |
| RTOD-Energy on-peak | $0.19307 per kWh | $0.24040 per kWh |
| RTOD-Demand energy charge | $0.06427 per kWh | $0.05725 per kWh |
| RTOD-Demand base-hours demand | $4.32 per kW | $4.20 per kW |
| RTOD-Demand peak-hours demand | $9.46 per kW | $10.81 per kW |
Sources: LG&E tariff, P.S.C. Electric No. 14, Sheets No. 5, 6 and 7, and KU tariff, P.S.C. No. 21, Sheets No. 5, 6 and 7, all issued August 28, 2026.
Three features of this table drive every comparison below:
- The basic service charge is the same on all three rates. It is also the minimum charge. Because it does not change when you switch, it drops out of any comparison, and the examples below leave it out.
- KU’s spread is wider. KU’s on-peak price is 3.08 times its off-peak price ($0.24040 / $0.07811); LG&E’s is 2.07 times ($0.19307 / $0.09312). At KU, shifting is rewarded more and unshifted use costs more.
- The “variable” part is the same in every hour. Each tariff splits the energy charge into an infrastructure part and a variable part for costs such as fuel. LG&E’s variable part is $0.04018 per kWh on every rate and in every period (KU’s is $0.04019); the on-peak premium sits entirely in the infrastructure part.
The LG&E and KU time-of-day web page still showed older figures in November 2026, for example $0.09177 and $0.19172 for LG&E’s RTOD-Energy and $0.06292 for its RTOD-Demand energy charge. The tariff is the record; use its numbers.
When the on-peak hours fall, on the tariff clock and on yours
RTOD-Energy’s on-peak hours are weekdays only: 1 to 5 p.m. from April through October, and 6 to 10 a.m. plus 6 to 10 p.m. from November through March. Weekends are off-peak all day. The catch is the clock: both tariffs say the rating periods “are established in Eastern Standard Time year-round” (Sheet No. 6.1), so in daylight time every window sits one hour later on your wall clock.
That puts the summer peak at 2 to 6 p.m. on an Eastern clock. The winter windows move between standard and daylight time too, because daylight time starts in March and ends in early November, inside the winter season. The LG&E and KU web page translates the windows into clock time for each part of the year, and for customers in the Central Time Zone, who see each window one hour earlier.
| Weekdays, by date range | Eastern clock | Central clock |
|---|---|---|
| January 1 to the second Saturday in March | 6 to 10 a.m. and 6 to 10 p.m. | 5 to 9 a.m. and 5 to 9 p.m. |
| Second Sunday in March to March 31 | 7 to 11 a.m. and 7 to 11 p.m. | 6 to 10 a.m. and 6 to 10 p.m. |
| April 1 to October 31 | 2 to 6 p.m. | 1 to 5 p.m. |
| November 1 to the first Saturday in November | 7 to 11 a.m. and 7 to 11 p.m. | 6 to 10 a.m. and 6 to 10 p.m. |
| First Sunday in November to December 31 | 6 to 10 a.m. and 6 to 10 p.m. | 5 to 9 a.m. and 5 to 9 p.m. |
The calendar shifts the short transition periods each year. Daylight time ended on Sunday, November 1, 2026, so that year’s November transition had no weekdays at all. In 2027, daylight time starts on March 14 and ends on November 7, so the 7 to 11 windows apply from March 15 to 31 and from November 1 to 5 on weekdays.
Two more rules complete the calendar. “If a legal holiday falls on a weekday, it will be considered a weekday,” so Thanksgiving and the Fourth of July can be on-peak days. And the seasons follow calendar months, not billing periods, so a bill that runs from mid-March to mid-April will contain both winter and summer windows.
How many hours are on-peak in a year
Counting the weekdays in 2026 gives 153 summer weekdays at 4 hours and 108 winter weekdays at 8 hours: 612 plus 864, or 1,476 on-peak hours out of 8,760. That is 16.8% of the year’s hours. The share varies by month: July 2026 had 23 weekdays, so 92 of its 744 hours (12.4%) were on-peak, while January 2027 has 21 weekdays, so 168 of 744 hours (22.6%) are on-peak.
Those percentages matter because they set the starting point. A home that used exactly the same power every hour of the year would put about 17% of its kWh in on-peak hours. Real homes are not flat: summer air conditioning peaks in the afternoon, and winter heating, cooking and showers cluster in the mornings and evenings, which is exactly where the windows sit.
The break-even test for RTOD-Energy
RTOD-Energy costs less than Rate RS when your on-peak share is below the break-even share. The break-even share is the flat price minus the off-peak price, divided by the on-peak price minus the off-peak price.
- LG&E: ($0.11499 minus $0.09312) / ($0.19307 minus $0.09312) = $0.02187 / $0.09995 = 21.9%.
- KU: ($0.11396 minus $0.07811) / ($0.24040 minus $0.07811) = $0.03585 / $0.16229 = 22.1%.
The two utilities land in almost the same place, but the stakes differ. Every off-peak kWh saves 2.19 cents against Rate RS at LG&E and 3.59 cents at KU; every on-peak kWh costs 7.81 cents more at LG&E and 12.64 cents more at KU. At KU, a home well below the break-even saves more, and a home well above it loses more.
| On-peak share of use | LG&E Rate RS | LG&E RTOD-Energy | KU Rate RS | KU RTOD-Energy |
|---|---|---|---|---|
| 10% | $114.99 | $103.11 | $113.96 | $94.34 |
| 15% | $114.99 | $108.11 | $113.96 | $102.45 |
| 20% | $114.99 | $113.11 | $113.96 | $110.57 |
| 22% | $114.99 | $115.11 | $113.96 | $113.81 |
| 25% | $114.99 | $118.11 | $113.96 | $118.68 |
| 30% | $114.99 | $123.10 | $113.96 | $126.80 |
| 35% | $114.99 | $128.10 | $113.96 | $134.91 |
Riders do not move the break-even much
The bill adds adjustment clauses to the base charges on every one of these rates. The fuel adjustment clause is a factor “per kWh delivered” and is “mandatory to all electric rate schedules” (LG&E Sheet No. 85), so it adds the same amount to each kWh whichever rate you are on. The environmental surcharge increases or decreases the monthly billing amount “by a percentage factor,” and Rate RS, RTOD-Energy and RTOD-Demand sit in the same group (Sheet No. 87). A per-kWh adder that is the same everywhere does not change the difference between two rates, and a percentage adder scales it a little. The break-even on base charges is a sound guide, though the bill itself is the final record.
Run the test month by month
A single annual share hides the seasons. A home can be at 15% in May and 30% in January and average out near the line, which means summer savings are being spent in winter. Compute the share for each month, price each month on both rates, and add the year. The rate plan comparison calculator prices one month at a time: for a two-period rate like RTOD-Energy, enter the off-peak price as the day price too. The general mechanics of time-of-use pricing, across other utilities’ schedules, are in the time-of-use rates guide.
How to find your own on-peak share
Your on-peak share comes from interval data: hourly or 15-minute readings from your smart meter, tagged by rating period. Rate RS bills show only monthly totals, so the bill alone cannot tell you.
LG&E and KU customers with an advanced meter can see their usage in the My Meter dashboard inside My Account and download it in the standard Green Button format. With a year of readings, the method has four steps:
- Put every reading on the tariff’s clock. During daylight time, the tariff’s 1 to 5 p.m. is 2 to 6 p.m. on an Eastern wall clock. Misreading it as wall-clock time moves the most expensive hour, 5 to 6 p.m. in summer, into off-peak.
- Tag each reading as on-peak or off-peak, using the weekday and holiday rules and the seasons above.
- Sum kWh by period for each month, and divide the on-peak kWh by the month’s total.
- Price each month on both rates and add the year.
Which loads land in the windows
Before you open a spreadsheet, it helps to know which loads usually decide the answer. The table describes common household loads against the RTOD-Energy windows; how large each is in your home is what the data shows.
| Load | Summer window (2 to 6 p.m. on the clock) | Winter windows (6 to 10 a.m. and 6 to 10 p.m. in standard time) | How easy to move |
|---|---|---|---|
| Central air conditioning | Runs hardest in these hours | Not a factor | Partly: pre-cool before the window and let the house drift a degree or two |
| Heat pump heating, backup strips | Not a factor | Early mornings are often the coldest hours; strips may run | Partly: start earlier at lower output; comfort sets the limit |
| Electric water heater | Afternoon showers or laundry | Morning showers, evening dishes | Easy with a timer or a heat pump water heater schedule |
| EV charging | Only if charging on a weekday afternoon | Charging on arrival at 6 p.m. lands in the evening window | Easy: charge after 10 p.m. in winter and outside 2 to 6 p.m. in summer |
| Cooking, oven, range | Late-afternoon cooking | Breakfast and dinner fall in the windows | Hard: meals happen when they happen |
| Laundry, dryer, dishwasher | Afternoon loads | Evening loads | Easy: delay start or run on weekends |
| Pool pump | Midday and afternoon runs | Usually off | Easy: set the timer outside the window |
If you have no interval data, estimate from routines and label the result an estimate. List the large loads that run on weekday afternoons in summer and on weekday mornings and evenings in winter: air conditioning, heat, cooking, laundry, dishwashing, showers with an electric water heater, and car charging on arrival. A home where someone is home all day, with the air conditioning running hard from 2 to 6 p.m., may well be above the line in summer unless it can pre-cool.
RTOD-Demand: a low energy price plus two demand charges
RTOD-Demand trades a much lower price per kWh for two charges per kW of demand, so it rewards homes that use a lot of energy at a steady, low rate of power. A home that runs several large loads at once, even for 15 minutes, pays for that moment all month.
The tariff defines demand as “the average kW demand delivered to the Customer during the 15-minute period of maximum use during the month” (Sheet No. 7.1). The rating periods divide the month into base hours, which are all hours, and peak hours, which match RTOD-Energy’s on-peak windows. In practice, that means two charges:
- Base-hours demand: your highest 15-minute demand at any time in the month, at $4.32 per kW (LG&E) or $4.20 (KU).
- Peak-hours demand: your highest 15-minute demand inside the weekday peak windows, at $9.46 per kW (LG&E) or $10.81 (KU).
Because base hours include peak hours, a spike in the peak counts for both. One 15-minute burst at 3 p.m. on a summer weekday, when an oven, a dryer and the air conditioner run together, sets both charges for the month.
Where RTOD-Demand breaks even with Rate RS
Against Rate RS, RTOD-Demand saves $0.05072 per kWh at LG&E ($0.11499 minus $0.06427) and $0.05671 at KU ($0.11396 minus $0.05725). It pays when those savings, multiplied by your monthly kWh, exceed the two demand charges. The table shows the monthly kWh at which the two rates come out even for a few combinations of demand.
| Highest 15-minute demand (base / peak) | LG&E demand charges | LG&E break-even use | KU demand charges | KU break-even use |
|---|---|---|---|---|
| 5 kW / 2 kW | $40.52 | 799 kWh | $42.62 | 752 kWh |
| 6 kW / 3 kW | $54.30 | 1,071 kWh | $57.63 | 1,016 kWh |
| 8 kW / 4 kW | $72.40 | 1,427 kWh | $76.84 | 1,355 kWh |
| 10 kW / 5 kW | $90.50 | 1,784 kWh | $96.05 | 1,694 kWh |
| 12 kW / 7 kW | $118.06 | 2,328 kWh | $126.07 | 2,223 kWh |
Arithmetic for the 8 kW / 4 kW row at LG&E: 8 x $4.32 = $34.56, plus 4 x $9.46 = $37.84, gives $72.40; $72.40 / $0.05072 = 1,427 kWh. Below that use, Rate RS is cheaper; above it, RTOD-Demand is.
RTOD-Demand or RTOD-Energy?
For a household already weighing RTOD-Energy, the useful comparison is between the two optional rates. At LG&E, RTOD-Demand’s energy charge is 2.89 cents below RTOD-Energy’s off-peak price ($0.09312 minus $0.06427) and 12.88 cents below its on-peak price ($0.19307 minus $0.06427). At KU the gaps are 2.09 cents off-peak ($0.07811 minus $0.05725) and 18.32 cents on-peak ($0.24040 minus $0.05725).
So RTOD-Demand beats RTOD-Energy when those per-kWh savings, added over the month, exceed the two demand charges. Most of the savings come from on-peak kWh, which means the homes that gain most from RTOD-Demand over RTOD-Energy are the ones that still use energy in the peak but at a low, steady rate of power. A KU home that has already pushed almost all of its use off-peak gains little from RTOD-Demand: 1,000 off-peak kWh save only 1,000 x $0.02086 = $20.86, which covers about 5 kW of base demand at $4.20 and nothing else.
The table above shows who RTOD-Demand suits: a large household, or one with an EV and electric heat, that uses well over 1,000 kWh a month and can keep its highest 15 minutes modest. Charger current matters a great deal. A Level 2 charger at 7.2 kW running overnight sets a base demand of at least 7.2 kW plus whatever else is on; the same car charged at a lower current over more hours sets a lower one. The car’s charging current setting, the charger’s settings and the circuit are things to confirm with the manufacturer’s documentation and a licensed electrician, not guesses. The guide to residential demand charges explains how demand is measured and how loads stack.
Which households gain, and which lose
The households that gain from a time-of-day rate are the ones with large loads that can move: an EV, a battery, a heat pump or water heater on a schedule. The ones that lose cannot move the use that falls in the windows. Here is how each common situation plays out on RTOD-Energy, the rate most households would consider first.
An EV charged after midnight
A car’s charging is the easiest large load to move, because it only needs to be full by morning. Suppose a car needs 11.1 kWh from the wall each day, the figure the site’s fictional example uses for 35 miles at 3.5 miles per kWh with a 10% charging loss. Over 30 days that is 333 kWh. On Rate RS it costs 333 x $0.11499 = $38.29 at LG&E or 333 x $0.11396 = $37.95 at KU. Charged off-peak on RTOD-Energy, it costs 333 x $0.09312 = $31.01 at LG&E or 333 x $0.07811 = $26.01 at KU.
That is $7.28 a month at LG&E and $11.94 at KU, before the rest of the house is counted. The car also pulls the household’s on-peak share down, because it adds off-peak kWh to the total. Charging on arrival at 6 p.m. does the opposite in winter, when 6 to 10 p.m. is on-peak.
A home battery
A battery can carry off-peak energy into the on-peak window, where the equipment and the interconnection agreement allow grid charging. NREL uses 85% as a representative round-trip efficiency for home batteries (NREL Annual Technology Baseline 2024), so each kWh delivered takes 1 / 0.85 = 1.18 kWh to charge. At LG&E, each kWh delivered on-peak is worth $0.19307 minus $0.09312 / 0.85 = $0.19307 minus $0.10955 = $0.08352 after losses. At KU it is worth $0.24040 minus $0.07811 / 0.85 = $0.24040 minus $0.09189 = $0.14851.
Winter is harder: two windows a day, eight hours apart, and short days with little solar to refill the battery between them. A battery sized for the summer afternoon may cover only one of the two winter windows.
A heat pump, a water heater and the winter mornings
In winter, the 6 to 10 a.m. window lands on cold early-morning hours and on showers and breakfast. A heat pump that warms the house before the window opens, and coasts through it a degree or two cooler, moves use out of the peak; backup resistance strips that kick in at 7 a.m. move it in. A water heater on a timer that heats before 6 a.m. and again after 10 a.m. shifts a predictable block. Comfort limits come first, and the setting changes belong to the homeowner and the equipment’s documentation.
Solar homes
Rooftop solar helps in summer, because the panels still produce during part of the 2 to 6 p.m. window and cut on-peak purchases. How exports are credited depends on the net metering rider. Under NMS-2, for systems in service on or after September 24, 2021, each exported kWh earns a flat bill credit of $0.07089 at LG&E or $0.07534 at KU at any hour (Sheet No. 58), so solar used at home during on-peak hours is worth far more than solar sent out. Under NMS-1, for older systems, credits created in one time-of-day block offset only use in the same block (Sheet No. 57). The Kentucky net metering guide covers both riders in full.
Who usually loses
A household with someone home all day in summer, running air conditioning hard through the afternoon, and with breakfast, showers and heat stacked into winter mornings and evenings, is likely to be above the break-even and pay more. So will a home that relies on electric resistance heat on cold mornings. LG&E and KU say so plainly: “If you do not shift the time of day that you use energy or you consume energy during on-peak times, your bill may go up.”
Worked examples with current LG&E and KU prices
These three households are fictional. The prices are the real base energy charges effective September 1, 2026, without the basic service charge (the same on every rate), riders or taxes. Totals are added before rounding to the cent, and differences are taken from the totals shown.
Example (fictional). A Louisville home on LG&E, no EV. In a summer month the home uses 1,000 kWh, and its interval data shows 260 kWh (26%) in weekday on-peak hours.
- Rate RS: 1,000 x $0.11499 = $114.99.
- RTOD-Energy as it lives now: 260 x $0.19307 = $50.20, plus 740 x $0.09312 = $68.91, total $119.11. That is $4.12 more than Rate RS.
- RTOD-Energy after moving 60 kWh (dishwasher and laundry after 6 p.m., pre-cooling before 2 p.m.): 200 x $0.19307 = $38.61, plus 800 x $0.09312 = $74.50, total $113.11. That is $1.88 less than Rate RS.
At LG&E, a home without a large movable load gains little even when it shifts.
Example (fictional). The same LG&E home adds an EV. The car adds 333 kWh a month, charged after midnight, and the home keeps the shifts from the first example. The month is 1,333 kWh with 200 kWh on-peak, a share of 15.0%.
- Rate RS: 1,333 x $0.11499 = $153.28.
- RTOD-Energy: 200 x $0.19307 = $38.61, plus 1,133 x $0.09312 = $105.50, total $144.12. That is $9.16 less than Rate RS.
- RTOD-Demand, charging at 7.2 kW: energy 1,333 x $0.06427 = $85.67. The highest 15 minutes of the month is 8.0 kW, overnight with the car and the house; the highest inside the peak is 4.5 kW, on a hot afternoon. Demand: 8.0 x $4.32 = $34.56, plus 4.5 x $9.46 = $42.57. Total $162.80, which is $9.52 more than Rate RS.
- RTOD-Demand with discipline: the car charges at a lower current over more hours, cooking and laundry stay out of the peak, and the house pre-cools. Base demand falls to 6.0 kW and peak demand to 3.0 kW: $85.67 + (6.0 x $4.32 = $25.92) + (3.0 x $9.46 = $28.38) = $139.97. That is $13.31 less than Rate RS and $4.15 less than RTOD-Energy.
The risk is one slip. A single 15-minute burst of 6.0 kW during a weekday peak would raise peak demand by 3.0 kW and add 3.0 x $9.46 = $28.38 to that month.
Example (fictional). A Lexington all-electric home on KU in January. The heat pump home uses 1,800 kWh in January, with 540 kWh (30%) in the 6 to 10 a.m. and 6 to 10 p.m. windows.
- Rate RS: 1,800 x $0.11396 = $205.13.
- RTOD-Energy as it lives now: 540 x $0.24040 = $129.82, plus 1,260 x $0.07811 = $98.42, total $228.23. That is $23.10 more than Rate RS.
- RTOD-Energy after moving 180 kWh (pre-heating before 6 a.m., the water heater on a timer, dishwasher and laundry midday): 360 x $0.24040 = $86.54, plus 1,440 x $0.07811 = $112.48, total $199.02. That is $6.11 less than Rate RS.
In KU territory, winter decides the answer for an all-electric home: the same rate that saves in a mild month can cost more than $20 extra in a cold one if nothing moves.
None of these is a forecast for a real home. One month is not a year, weather and household routines change the share, and riders move every bill. The example home on this site uses a fictional example rate rather than LG&E’s or KU’s prices, so its numbers do not carry over to these tariffs.
The fine print: meter, cap, 12-month rule and billing
The tariffs attach conditions that matter as much as the prices. Read these before you call.
| Condition | What the tariff says | What it means for you |
|---|---|---|
| Meter | Available to customers who qualify for Rate RS “and have an electric AMI meter” | No smart meter, no time-of-day rate; a home that opted out of AMI would need to opt back in |
| Enrollment cap | “Limited to a maximum of five hundred (500) Customers” on RTOD-Energy and RTOD-Demand combined, “first-come-first-served” | Each utility’s tariff sets its own cap of 500; the tariff does not say how many places are open, so ask |
| Leaving | A customer who returns to Rate RS “may not be allowed to return to this optional rate for twelve (12) months” | Treat the switch as at least a year-long decision |
| Budget billing | Customers on these optional rates “will not be eligible for Company’s Budget Payment Plan” | Bills will swing with the seasons; plan for winter |
| Holidays | A legal holiday on a weekday “will be considered a weekday” | Holiday afternoons and evenings can be on-peak |
| Detached garage | Also available on a Rate GS service to a detached garage using no more than 300 kWh a month, where the power is used in part for low-emission vehicles licensed for public roads, such as plug-in electric vehicles | A narrow option; ask the utility whether it fits your service |
Sources: LG&E and KU tariffs, Sheets No. 6, 6.1, 6.2, 7 and 7.2.
What the tariff does not tell you
A tariff sets the rules but not the queue. Before you switch, ask the utility four things the sheets cannot answer: whether places are open under the 500-customer cap at your utility, whether your installed meter already qualifies, on which day of your billing cycle the new rate would start, and whether your bill will show kWh by rating period so you can check each month against your own estimate.
Two other points are worth noting. The basic service charge is the minimum charge on all three rates, so a month with almost no use still costs $0.48 or $0.58 a day. And the tariffs say the company “shall install metering equipment capable of accommodating” the rate, so the meter question is the utility’s to answer, not yours.
How the 2026 rate cases changed the numbers
The prices in this guide come from two rounds of orders in 2026. Base rates changed after the PSC’s February 16, 2026 orders, and energy charges changed again on September 1, 2026 after orders on the fuel adjustment clause.
- February 16, 2026. LG&E and KU’s rate request page says that on February 16, 2026 “the Kentucky Public Service Commission approved new base rates for LG&E and KU,” after interim rates began on January 1. Based on average residential usage, it puts the change at about $5.14 more per month for an LG&E electric customer and about $8.73 more for a KU electric customer. The current tariff sheets cite the orders in Case No. 2025-00114 (LG&E) and Case No. 2025-00113 (KU).
- September 1, 2026. The Rate RS, RTOD-Energy and RTOD-Demand sheets were revised again under orders dated August 18, 2026, in Case No. 2025-00341 for LG&E and Case No. 2025-00340 for KU. The LG&E case was a review of the fuel adjustment clause: the PSC’s order set a base fuel cost of $0.02987 per kWh and raised base energy rates by $0.00127 per kWh for service on and after September 1, 2026.
Rates will change again. Any comparison you make should cite the sheet and its effective date, and you should rerun it when a new sheet is issued. The rating periods sit on Sheet No. 6.1, effective February 16, 2026; the September revision changed the prices, not the windows.
How to decide, and how to switch
Decide from your own data, month by month, with the current sheets in front of you. If the answer is close, the 12-month rule and the loss of budget billing are good reasons to wait until you have a load you can move.
- Download twelve months of interval data from My Meter, and note any month with a new car, heat pump, solar array or an empty house.
- Tag each reading with RTOD-Energy’s periods on the tariff’s clock, and compute your on-peak share for each month.
- Compare each month with the break-even: 21.9% at LG&E, 22.1% at KU. Price the year on Rate RS and RTOD-Energy.
- For RTOD-Demand, find your highest 15-minute demand in each month, overall and inside the peak windows, and compare with the break-even table.
- List what you could move, and when: the car, the battery, pre-heating and pre-cooling, the water heater, laundry. Recompute with those moves, and be honest about winter mornings.
- Check the conditions: an AMI meter, the cap, the 12-month rule and budget billing.
- Call to ask about enrollment. The time-of-day page lists 502-589-1444 for LG&E and 800-981-0600 for KU, then options 1, 2 and 4, and says a representative will help you choose. Ask whether places are open under the 500-customer cap and when the change would take effect in your billing cycle.
The Louisville, Kentucky page summarizes the local rate context in brief. Culni is not affiliated with LG&E or KU, and the utility decides who may join a rate. If you want this comparison run on your own interval data, the rate engine page explains how Culni reads a schedule like RTOD-Energy, and you can send your rate, a recent bill and your device list through the contact page.
