Culni homeCheck my home
Menu

The best electricity rate for EV charging: whole-home TOU, EV rate or flat

An EV time of use rate, a separate EV meter or a flat rate: compare cost per mile, fixed charges, meter costs and what the rest of your house pays on peak.

Reader question
Which electricity rate plan makes home EV charging cheapest for my household, and what does each option cost per mile?
A railway switch where one track divides into two under a crescent moon, with the switch lever set toward the quieter, darker line.

The cheapest rate for home EV charging is the one that gives the car a long, low-priced window overnight without costing the rest of the house more on the peak than the car saves. A whole-home time-of-use or EV rate beats a flat rate when the car charges off-peak and enough of the household’s own use stays out of the peak hours; a separately metered EV rate pays only when its meter, wiring and monthly charge cost less than the house would lose on peak prices. To compare any two plans, convert each to cost per mile: your car’s kWh per 100 miles times the price in the hours it actually charges, plus any fixed charge the plan adds, spread over the miles you drive.

This article covers the rate decision. Whether a 120-volt outlet can fill the car inside an off-peak window is in Level 1 vs Level 2 home charging, and the monthly arithmetic for your own miles is what the EV charging cost calculator does. Every price below is as of November 2026 and is a base charge from the utility’s published tariff or rate page, before riders, supply adjustments and taxes unless stated otherwise.

Three ways utilities price home EV charging

Utilities price home charging in three ways: the car shares a time-of-use rate with the whole house, the car gets its own meter and its own rate, or the house stays on a standard rate and the car earns program incentives or is measured through a submeter. The U.S. Department of Energy’s EV Grid Assist webinar summary on rates describes the same three metering choices from the rate designer’s side: measure the EV “along with all other loads at the location with the premise meter (often referred to as a whole home rate)”, install a second utility meter for the EV alone, or use submetering “through the EV supply equipment or vehicle”.

The same DOE summary lists the pieces any of these rates can carry: a volumetric energy charge per kWh, a demand charge tied to peak kW, and a customer charge “to cover the cost of connecting a customer to the grid, such as metering, billing, and accounting costs”. Those three pieces are where the real comparison happens, because an EV rate with a low price per kWh can still lose once its customer charge or its peak hours are counted.

Structure How the car is metered Examples as of November 2026 What you give up
Whole-home time-of-use or EV rate One meter for house and car LG&E RTOD-Energy, PG&E EV2-A, Central Hudson EV whole home, Con Edison residential time-of-use Every load in the house pays the peak price during peak hours
Separately metered EV rate A second utility meter for the charger only PG&E EV-B, Con Edison EV-only meter, Central Hudson separate meter option Wiring, a meter socket and a second monthly charge; some bill protection offers do not apply
Standard rate plus a program or submeter One meter; the charger or car reports charging Con Edison SmartCharge New York on the standard rate, LG&E and KU Optimized EV Charging The price per kWh does not fall; the utility may shift charging on event days

The flat rate is the baseline

A flat rate charges the same energy price at every hour. LG&E’s standard residential Rate RS, for example, charges $0.11499 per kWh plus a Basic Service Charge of $0.48 per day (LG&E tariff Sheet No. 5, effective September 1, 2026). Every option below is worth taking only if it beats that baseline for the whole bill, not just for the car’s share of it.

How to turn any rate into cost per mile

Cost per mile is the car’s energy use per mile multiplied by the price per kWh in the hours it charges, plus any fixed charge the plan adds divided by the miles you drive. It is the one number that lets you compare a Kentucky time-of-day rate, a California EV rate and a New York delivery charge on the same footing.

The energy figure comes from the EPA rating on fueleconomy.gov, listed in kWh per 100 miles. That figure is measured from the wall: the EPA says its MPGe values “include charging losses”, assume Level 2 AC charging, and account for losses in the charging cable, which “moves the measurement from the vehicle to the outlet in the wall”. So you do not add a separate charging loss to an EPA kWh per 100 miles figure.

  1. Look up your car. On fueleconomy.gov, the 2026 Chevrolet Equinox EV FWD is rated at 31 kWh per 100 miles (108 MPGe combined). That is 0.31 kWh per mile.
  2. Find the price in your charging hours. Use the tariff sheet’s energy charge for the window the car will actually charge in, not the plan’s headline number.
  3. Multiply. 0.31 kWh per mile x $0.11499 per kWh = $0.0356, or 3.56 cents per mile on LG&E Rate RS.
  4. Add the fixed charges the plan adds. If a plan adds $20 a month and you drive 1,050 miles a month (35 miles a day for 30 days), that is $20 / 1,050 = 1.9 cents per mile.
  5. Compare the whole bill, not only the car. If the plan raises the price of the house’s own peak use, that cost belongs in the comparison too. The next sections show how.
Charging cost per mile for one car on six real rate windowsHorizontal bars for a car using 31 kWh per 100 miles. LG&E RTOD-Energy off-peak 2.89 cents per mile, LG&E Rate RS 3.56, LG&E RTOD-Energy on-peak 5.99, PG&E EV2-A off-peak 6.99, PG&E EV-B summer off-peak 8.20, PG&E EV2-A summer peak 16.68. Cents per mile at 31 kWh per 100 miles LG&E RTOD off-peak 2.89 LG&E Rate RS (flat) 3.56 LG&E RTOD on-peak 5.99 PG&E EV2-A off-peak 6.99 PG&E EV-B off-peak, summer 8.20 PG&E EV2-A peak, summer 16.68 0 5 10 15
Cost per mile = 0.31 kWh per mile x energy price. LG&E: Rate RS and RTOD-Energy base energy charges before riders and taxes (Sheet Nos. 5 and 6, effective September 1, 2026). PG&E: total bundled energy rates from Schedule EV2 Sheet 2 (effective June 1, 2026) and Schedule EV Sheet 2 (effective March 1, 2026), before daily charges. Car: 2026 Chevrolet Equinox EV FWD, fueleconomy.gov. Checked November 2026.

Here is the arithmetic behind each bar, so you can redo it for your own car and utility.

Rate window Price per kWh x 0.31 kWh per mile Cost per mile
LG&E RTOD-Energy, off-peak $0.09312 0.31 x 9.312 cents 2.89 cents
LG&E Rate RS, any hour $0.11499 0.31 x 11.499 cents 3.56 cents
LG&E RTOD-Energy, on-peak $0.19307 0.31 x 19.307 cents 5.99 cents
PG&E EV2-A, off-peak (all year) $0.22558 0.31 x 22.558 cents 6.99 cents
PG&E EV-B, off-peak, summer $0.26465 0.31 x 26.465 cents 8.20 cents
PG&E EV2-A, peak, summer $0.53809 0.31 x 53.809 cents 16.68 cents

Two cautions apply. The LG&E numbers are base charges: the tariff lists adjustment clauses for demand-side management, fuel, off-system sales, environmental costs, retired assets, pilot generation, home energy assistance, franchise fees and school tax that apply on top, so your bill’s all-in price per kWh will be higher. And the cost per mile rises in cold weather, when the same car uses more kWh per mile; the Level 1 vs Level 2 article works through what that does to the charging window.

Whole-home time-of-use: the car gets the low price, the house gets the peak

A whole-home time-of-use rate prices every kWh the house uses by the hour, so the car’s overnight charging gets the low price and so does everything else that runs off-peak. The trade is that the dryer, oven, water heater and air conditioner pay the higher price whenever they run in the peak window. Four published examples show how differently utilities draw those windows.

LG&E RTOD-Energy (Kentucky)

LG&E’s Residential Time-of-Day Energy rate, Sheet Nos. 6 and 6.1, charges $0.09312 per kWh off-peak and $0.19307 per kWh on-peak, with the same $0.48 daily Basic Service Charge as Rate RS (effective September 1, 2026). Its rating periods are set in Eastern Standard Time all year:

  • April through October, weekdays: on-peak 1 p.m. to 5 p.m.; off-peak 5 p.m. to 1 p.m.
  • November through March, weekdays: on-peak 6 a.m. to 10 a.m. and 6 p.m. to 10 p.m.; off-peak 10 a.m. to 6 p.m. and 10 p.m. to 6 a.m.
  • Weekends: all hours off-peak. A legal holiday on a weekday counts as a weekday.

Because the windows stay on standard time, they read one hour later on the clock while daylight saving time is in effect. LG&E’s time-of-day page shows the summer on-peak as 2 p.m. to 6 p.m. EDT. The rate is optional, needs “an electric AMI meter”, and is “limited to a maximum of five hundred (500) Customers” on RTOD-Energy and RTOD-Demand combined, first come, first served. A customer who leaves it for Rate RS may not be allowed back for twelve months.

For a car that plugs in at 6 p.m. and leaves at 7:30 a.m., the two seasons look very different. In summer, the whole evening and night are off-peak on the clock, so the car can charge as soon as it arrives. In winter, 6 p.m. to 10 p.m. and 6 a.m. to 10 a.m. are both on-peak, so the charge has to fit between 10 p.m. and 6 a.m.: eight hours. The LG&E and KU time-of-day article covers these windows in more detail.

PG&E EV2-A (California)

PG&E’s Schedule EV2 applies “to whole house service where the residential usage and the electric vehicle charging usage is metered together”. Peak is 4 p.m. to 9 p.m. every day including weekends, partial-peak is 3 p.m. to 4 p.m. and 9 p.m. to midnight, and every other hour is off-peak, which makes midnight to 3 p.m. the cheap stretch. Summer runs June 1 through September 30.

The total bundled energy rates on Sheet 2, effective June 1, 2026, are $0.53809 peak, $0.42760 partial-peak and $0.22558 off-peak per kWh in summer, and $0.41099, $0.39428 and $0.22558 in winter. The schedule also carries a monthly base services charge billed by the day and set by income tier: $0.19713, $0.39688 or $0.79343 per day. A household on EV2 cannot exceed 800% of its annual baseline allowance; above that, the schedule moves it off the EV rate. PG&E’s EV rate page adds that a residential customer may change rate schedules twice in the first 12 months; after the second change, the customer must stay on that rate for 12 months.

Central Hudson EV whole home (New York)

Central Hudson’s EV Time of Use Rate, read from an archived copy of the utility’s page dated October 8, 2026 because the live page returned a bot check, puts the peak at 2 p.m. to 7 p.m. on weekdays. Weekends and six holidays are off-peak. The utility states plainly that “you must shift use of approximately 83% of your electricity during off-peak hours” to save, and that you must sign on for a minimum of one year.

The whole-home option comes with first-year bill protection: if the year would have cost less on standard rates, Central Hudson refunds the difference. That protection ends after the first year. Its supply charge on this rate follows hourly market prices, so the off-peak price is not a single published number.

Con Edison residential time-of-use (New York)

Con Edison’s EV page shows a different shape: the peak runs 8 a.m. to midnight and off-peak is midnight to 8 a.m. Delivery is $0.2786 per kWh in peak hours from June 1 to September 30, $0.1711 in peak hours the rest of the year, and $0.0522 off-peak all year, with electricity supply billed on top. The monthly customer charge on the time-of-use rate is $21.00.

Con Edison compares your first 12 months on the rate with what the standard rate would have cost and credits the difference if you paid more. You must stay enrolled for a year, and if you switch back to the standard rate you cannot rejoin for 18 months. Summer Super-Peak supply pricing, June through September on weekdays from 2 p.m. to 6 p.m., applies to customers who buy supply from Con Edison.

The break-even question: how much of the house runs on peak

A whole-home rate pays when the car’s savings plus the savings on the house’s off-peak use exceed the extra paid on the house’s peak use. You can find the break-even point with three numbers: the flat price, the off-peak price and the on-peak price.

Take LG&E’s numbers. Against Rate RS, every off-peak kWh on RTOD-Energy saves $0.11499 minus $0.09312, or 2.187 cents, and every on-peak kWh costs $0.19307 minus $0.11499, or 7.808 cents more. The daily Basic Service Charge is $0.48 on both rates, so it cancels out. Suppose a household uses 900 kWh a month, close to the US average of about 899 kWh a month that the EIA reported for 2022, and adds a car that draws 333 kWh a month, all of it off-peak.

  • Without the car: the rate breaks even when 7.808 x the on-peak share = 2.187 x the off-peak share. That is an on-peak share of 2.187 / (7.808 + 2.187) = 21.9% of the house’s kWh.
  • With the car: the car’s 333 kWh save 333 x $0.02187 = $7.28 a month, which lets the house carry more on-peak use. Solving 900 x p x $0.07808 = (900 x (1 minus p) + 333) x $0.02187 gives p = 30.0%.
Monthly cost of LG&E RTOD-Energy minus Rate RS by on-peak share of household useTwo rising lines. For a 900 kWh house alone, RTOD-Energy saves $19.68 a month at 0% on-peak and breaks even at 21.9%. With a car adding 333 kWh off-peak, it saves $26.97 at 0% and breaks even at 30.0%. At 40% on-peak the house alone pays $16.30 more and the house with the car pays $9.02 more. RTOD-Energy minus Rate RS, dollars per month +20 +10 0 -10 -20 -30 0% 10% 20% 30% 40% 21.9% 30.0% House only, 900 kWh House plus car, 333 kWh off-peak
Hypothetical household of 900 kWh a month, with and without a car drawing 333 kWh a month off-peak. Base energy charges before riders and taxes: LG&E Rate RS $0.11499, RTOD-Energy $0.09312 off-peak and $0.19307 on-peak (Sheet Nos. 5 and 6, effective September 1, 2026). The $0.48 daily charge is the same on both rates and is left out. Below zero, RTOD-Energy costs less.

Now compare those break-even shares with the windows. In summer, LG&E’s on-peak covers 4 hours on 5 weekdays, which is 20 of the 168 hours in a week, or 11.9%. In winter it covers 8 hours on 5 weekdays, 40 of 168 hours, or 23.8%. A household whose use were spread evenly across the hours would land well under the 30% break-even in summer and close to it in winter, before any effort to shift. Real households are not even: winter mornings and evenings, when people shower, cook and heat the house, fall inside LG&E’s winter peaks, which is why the utility says “If you do not shift the time of day that you use energy or you consume energy during on-peak times, your bill may go up.”

You do not need to guess your on-peak share. If you have an AMI meter, your utility account usually shows hourly use, and adding up the kWh inside the peak hours for a few winter and summer weeks gives you the share directly. The time-of-use rates article explains how to read hourly data against a rate’s windows.

Separately metered EV rates: a cheaper car, a second meter

A separately metered EV rate puts the charger on its own utility meter and its own rate, so the house keeps its existing plan and only the car is priced by the hour. It removes the house’s peak risk, but it adds an electrician’s job, a meter socket and a second monthly charge, and the EV-only price per kWh is not always lower than the whole-home one.

PG&E EV-B

PG&E’s Schedule EV now offers only Rate B, which “Applies to all applicable customers with a separately metered BEV or PHEV recharging outlet.” Its peak is 2 p.m. to 9 p.m. on weekdays and 3 p.m. to 7 p.m. on weekends and holidays; partial-peak is 7 a.m. to 2 p.m. and 9 p.m. to 11 p.m. on weekdays; every other hour is off-peak. Summer runs May through October.

The total bundled energy rates on Sheet 2, effective March 1, 2026, are $0.62131 peak, $0.37720 partial-peak and $0.26465 off-peak per kWh in summer, and $0.43878, $0.30677 and $0.23504 in winter, plus a meter charge of $0.04928 per day. Set against EV2-A, the EV-only off-peak price is higher in both seasons: 26.465 cents in summer against 22.558 cents, and 23.504 cents in winter against 22.558 cents. The EV-only meter’s own daily charge is small, about $1.48 for a 30-day month, but the house still pays whatever its own rate charges on the first meter.

Con Edison EV-only meter

Con Edison lets you “install a separate residential meter solely to charge your electric vehicle”. The page is direct about the work involved: “You’ll need to hire a licensed electrician to do the necessary wiring, and to install a new meter pan and panel.” The second meter adds a $20 monthly customer charge, it is not covered by the first-year price protection, and it makes you ineligible for SmartCharge New York incentives.

That $20 is a cost per mile of its own. At 1,050 miles a month it adds $20 / 1,050 = 1.9 cents per mile before a single kWh is counted, which is more than half the car’s whole energy cost per mile on LG&E’s flat rate in the table above.

Central Hudson separate meter option

Central Hudson’s separate meter option is “specifically for customers who have installed a separate meter for the exclusive purpose of charging their electric vehicle.” It is not eligible for first-year bill protection; the utility’s reasoning is that a separately metered car gives the customer more control over when the electricity is used.

Kentucky: no residential EV-only rate at LG&E

LG&E’s residential customers are those served on Rate RS, RTOD-Energy or RTOD-Demand, and its EVSE charging-station rate is offered to general service and larger customers. There is one metering path worth knowing. The RTOD-Energy sheet also makes the rate available where a Rate GS meter serves a detached garage alongside a Rate RS home, the garage uses no more than 300 kWh a month, and some of that power charges a licensed plug-in vehicle.

Check the 300 kWh limit against your miles. The site’s fictional example car, which drives 35 miles a day at 3.5 miles per kWh with a 10% charging loss, draws about 333 kWh a month, which is already over it. A garage that stays on Rate GS pays its own Basic Service Charge of $1.35 a day for single-phase service, about $40.50 for a 30-day month, and an energy charge of $0.13390 per kWh (Sheet No. 10, effective September 1, 2026).

When a second meter makes sense

A second meter is worth pricing when three things are true: the house cannot move much of its use out of the peak, the EV-only off-peak price is well below the house’s current price, and the meter and wiring cost little because the panel and the parking spot are close together. Even then, the decision hinges on the monthly charge. Divide it by your monthly miles and add the result to the EV rate’s cost per mile before you compare.

Second-meter cost Example as of November 2026 Per mile at 1,050 miles a month
Monthly customer or meter charge Con Edison: $20 a month; PG&E EV-B: $0.04928 a day 1.9 cents; 0.14 cents
Electrician, meter socket and panel Required at Con Edison; quoted by your electrician Spread over the years you expect to keep the car
Lost bill protection Con Edison and Central Hudson exclude separate meters Only matters if the whole-home rate was uncertain
Lost program incentives Con Edison: no SmartCharge New York with an EV-only meter The incentive you would have earned, per mile

Standard rate plus a program: paid to shift, priced flat

Some utilities leave the house on its standard rate and pay the driver to charge at the right times, or let the utility move charging on a limited number of days. The price per kWh stays the same, so the value is the incentive divided by your miles.

Con Edison says EV owners on the Standard Residential Rate “can also earn incentives for charging during times of the day when demand for electricity is lower through the SmartCharge New York program”, and that enrolling the whole house in time-of-use or adding an EV-only meter ends that eligibility. In Kentucky, the LG&E and KU Optimized EV Charging program pays “$25 plus an additional $5 monthly participation incentive” to residential customers who enroll a qualifying networked Level 2 charger or EV and let the utility optimize the daily charging schedule. It may also adjust charging during “up to 10 demand response events during the year”; drivers can override the schedule, but participants who opt out of those events forgo the monthly incentive and may be removed from the program.

Price that incentive per mile. On LG&E Rate RS, the Equinox example costs 3.56 cents per mile; $5 a month over 1,050 miles is 0.48 cents per mile, which brings the car to about 3.09 cents. RTOD-Energy’s off-peak charging is 2.89 cents per mile with no program attached, but it carries the house’s peak risk. Whether you can combine a program with a time-of-use rate is a question for the program’s terms, and the managed EV charging programs article compares program types in detail.

PG&E offers a middle path on the whole-home rate: customers on EV2-A who are not on net energy metering may use a PG&E-approved EV submeter to measure the car’s charging separately, under the submetering protocol adopted in Decision 22-08-024. It does not change the price; it changes what is measured.

The costs that decide the answer beyond the price per kWh

The headline off-peak price is usually the least decisive number on an EV rate. Fixed charges, meter costs, enrollment limits and the house’s peak use move the total more often than a cent or two on the off-peak price. Check each line before you switch.

What to check Where to find it Example as of November 2026 Why it matters
Daily or monthly fixed charge The RATE section of the tariff sheet LG&E: $0.48 a day on both RS and RTOD-Energy; Con Edison: $21.00 a month on time-of-use; PG&E EV2: base services charge by income tier If it differs between plans, divide it by your monthly miles
Second meter and wiring The utility’s EV page; your electrician’s quote Con Edison: licensed electrician, new meter pan and panel, $20 a month Often the largest single cost of an EV-only rate
Meter requirement The AVAILABILITY section LG&E RTOD-Energy needs an AMI meter No eligible meter, no rate
Enrollment cap The AVAILABILITY section LG&E: 500 customers on RTOD-Energy and RTOD-Demand combined The rate may be closed when you apply
Minimum stay and lockout The tariff or the utility’s FAQ LG&E: 12 months before returning after leaving; Con Edison: one year minimum, 18 months to rejoin; Central Hudson: one year minimum A bad fit costs you a year
Bill protection The utility’s EV page Central Hudson and Con Edison compare your first year and refund or credit the difference Lowers the risk of a whole-home trial
Season and time standard The rating periods LG&E windows are in Eastern Standard Time all year; PG&E EV2 summer is June to September, EV-B summer is May to October Clock times shift with daylight saving; prices shift with seasons
Usage limits The APPLICABILITY section PG&E EV2 and EV: no more than 800% of annual baseline Heavy users can be moved off the rate
Riders and supply charges The adjustment clauses; your bill LG&E lists nine adjustment clauses; Con Edison’s prices above are delivery only The all-in price is higher than the base charge
Program exclusivity The program terms Con Edison: no SmartCharge New York on time-of-use or an EV-only meter You may have to choose between a rate and a program

A worked comparison with the example rate

The site’s example home runs on a fictional time-of-use rate so the arithmetic stays simple. It is not a utility tariff, and the numbers below are an illustration of the method, not a forecast for any home.

Example (fictional). The example home’s car drives 35 miles a day at 3.5 miles per kWh with a 10% charging loss, so it draws 11.1 kWh from the wall a day, or about 333 kWh in a 30-day month. The example rate charges 8 cents per kWh off-peak (9 p.m. to 7 a.m.), 14 cents in the day (7 a.m. to 4 p.m.) and 31 cents on peak (4 p.m. to 9 p.m. on weekdays); the flat-rate comparison is 13 cents.

For the car alone, the EV charging cost calculator gives $103.33 a month if the car charges on arrival in the peak and $26.67 a month off-peak, a difference of $76.67, or 2.5 cents per mile off-peak. On the flat rate the same 333.3 kWh cost 333.3 x $0.13 = $43.33.

Now add the house. The rate plan comparison calculator prices a 900 kWh month with 25% of use in peak hours, 30% in day hours and 45% off-peak at $139.95 on the time-of-use rate and $117.00 on the flat rate, $22.95 more for time-of-use. With the car on each plan, the totals are $139.95 + $26.67 = $166.62 on time-of-use and $117.00 + $43.33 = $160.33 on flat. The flat rate still wins by $6.29 a month: the car’s $16.66 advantage does not cover the house’s peak use.

Move some of the house’s use instead. If the household shifts the dishwasher, laundry and water heating so that 15% of its use falls in peak hours and 55% off-peak, the house costs 900 x (0.15 x $0.31 + 0.30 x $0.14 + 0.55 x $0.08) = 900 x $0.1325 = $119.25 on time-of-use. With the car, that is $145.92 against $160.33 flat, and time-of-use is now $14.41 a month cheaper. These are monthly figures for one fictional pattern of use, not a yearly result.

The lesson carries over to real tariffs. The car alone rarely decides the rate; the house’s peak share does, and the car moves the break-even point by a predictable amount. The example home page shows the same car on a full day, with solar and a battery in the picture.

Which structure wins: a decision table

Use the table below once you know three things: your car’s kWh per 100 miles, roughly what share of your house’s use falls in each plan’s peak window, and the fixed charges each plan adds. The rows are rules of thumb built from the arithmetic above, not promises about any utility’s plan; run your own numbers before you switch.

Your situationStructure to price firstWhyCheck before switching
The car can charge in a long overnight window and the house's big loads can run outside the peakWhole-home time-of-use or EV rateBoth the car and much of the house get the low priceYour on-peak share against the break-even share; enrollment cap; lockout
The house has heavy loads you cannot move, such as electric heat on winter morningsStay on the flat rate, or price an EV-only meterThe house's peak cost can outweigh the car's savingsThe second meter's monthly charge per mile; the EV-only off-peak price
The utility offers first-year bill protection on the whole-home rateWhole-home time-of-use for a trial yearThe downside in year one is limited by the utility's own comparisonWhat happens after year one; the minimum stay
You drive few miles a monthFlat rate, possibly with a programA fixed charge spread over few miles costs more per mileProgram incentives per mile; any added customer charge
You drive many miles and the panel is close to the parking spotCompare whole-home time-of-use with an EV-only meterA second meter's fixed charge shrinks per mile as miles growWiring and meter socket cost; lost bill protection or incentives
Your utility pays for managed charging on the standard rateFlat rate plus the program, compared with time-of-useThe incentive per mile may close much of the gap without peak riskEvent rules, opt-out penalties and whether the program allows a time-of-use rate
Decision rules derived from the cost-per-mile and break-even arithmetic in this article; tariff details from LG&E, PG&E, Con Edison and Central Hudson pages and sheets cited above, checked November 2026.

A note on demand-based residential rates

Some utilities, including LG&E with its RTOD-Demand rate, offer residential rates that add a charge per kW of peak demand. A Level 2 charger drawing 7.2 kW for two hours uses 14.4 kWh but adds 7.2 kW to whatever else is running in that hour, so on a demand rate the hour the car charges can matter as much as the price per kWh. Price a demand rate only after you know when the charger, the dryer and the heating run, and treat it as a separate decision from the energy-only rates compared here.

Questions to settle with your utility before you switch

A rate switch is a paperwork step, but several of its terms are easy to miss on a rate page and hard to undo once you are enrolled. Ask these before you apply, and keep the answers with your bill.

  1. Is the rate open? Ask whether the enrollment cap has been reached and how long a waiting list runs, if there is one.
  2. Does my meter qualify? Some rates need an interval or AMI meter; ask whether yours already records hourly use.
  3. What are the exact windows on the clock? Get them for summer, winter and the weeks around daylight saving changes, and ask which holidays count as weekdays.
  4. What is the all-in price per kWh in each window? Ask for the base charge plus the riders that currently apply, or read them from a recent bill.
  5. What changes on the fixed side? Daily or monthly charges, a second meter’s charge, and any base services charge.
  6. How long must I stay, and when can I come back? Minimum stays and lockouts range from 12 to 18 months in the examples above.
  7. Is there first-year bill protection, and does it cover my option? Separate meters were excluded in both New York examples.
  8. Can I keep a program on this rate? Ask whether managed charging incentives or event programs can be combined with the rate.

What to do next

Start with the numbers you already have, then price the plans your utility actually offers. A short checklist keeps the comparison honest:

  • Look up your car’s kWh per 100 miles on fueleconomy.gov and your monthly miles.
  • Pull the energy charges and fixed charges for each plan from the tariff sheet, with the effective date.
  • Find your house’s share of use in each plan’s peak window from hourly data on your utility account.
  • Run the car through the EV charging cost calculator and the house through the rate plan comparison calculator, then add the two.
  • Add any second meter’s monthly charge per mile, and any program incentive per mile.
  • Read the minimum stay and the lockout before you sign up.

Once the rate is chosen, the charging schedule has to match it every night, including the winter weeks when the window splits and the days the car leaves early. Culni is software that reads a home’s electricity rate and runs one daily schedule across solar, a home battery, EV charging and flexible loads; its EV charging schedule fills the cheapest hours that still have the car ready by the departure time, through the charger or the car where a control path is confirmed for your home. The EV homes page covers households with one or two cars. If you want your own rate decoded with every assumption shown, you can send your rate plan, a recent bill and your device list.

TodayYour turn

Want this worked out for your home?

Send your utility and rate plan, one recent bill and the devices you have or plan. We reply with a written home energy plan and every assumption behind it.

Remote. No site visit needed.